Blog Layout

Ohio Health Department Approved Rainwater Harvesting Installation

Rain Brothers • October 30, 2024
How to set up a Rainwater Harvesting Cistern (concrete): Step by step how to

This is a step-by-step overview of one of our recent installations. This was installed using Ohio Health Department standards, which are the most stringent regulations in the USA. This is a 5500-gallon precast concrete cistern system. All components, including the concrete cistern, can be purchased through our catalog or by requesting a quote for  a system install.


How to set up a Rainwater Harvesting Cistern (concrete)


Step 1: Excavate cistern pit and bed pit
with 4-6" of crushed stone or sand with level bedding


Step 2: Dig trench (below frost level)
for water supply line to the house


Step 3: Drill hole through foundation wall
for waterline/electric


Step 4: Set cistern tank


Step 5: Connect water line and cabling
(electric) to cistern


Step 6: Dig downspout drainage trenching
. Install 4" Solid Core Schedule 4 PVC and bed pipe with crushed stone/sand/clean fill. 


Step 7: Install Roofwasher filter.
In this case we used our Wisy Vortex unit. 


Step 8: Install overflow
from Roofwasher/cistern


Step 9: Install
rodent/mosquito guard on overflow/discharge


Step 10: Bed roof washer filler with crushed stone
. Ensure all joints and wrapped/caulked using Wisy Vortex Filter


Step 11: Run any remaining drainage
. Ensure there is fall on the pipe so everything drains towards the cistern. 


Step 12: Backfill and grade


Note: Consider future excavation. Here we left the pipe exposed so septic contractors would locate our pipe easily when they dig into an area. 


Step 13: Install inside controls/filters
. Run waterline electric cabling through foundation wall and into pressure tank. (Pump is submersible and inside cistern). Install shut off valve immediately after pressure tank (downstream). Install two stage sediment reduction (down to 5 micron absolute). Be sure to use NSF approved filter housings. Install NSF Class A UV Sterilizer. Install smooth-nosed sample tamp immediately after filtration treatment, followed by main water shut off valve. Use hydraulic cement inside and outside to seal water line penetration. 


Optional: Install
tank level gauge


Request an estimate for a full system install


All components, including the concrete cistern, can be purchased through our catalog or by requesting a quote for  a system install.


Rainwater Harvesting System Installation
Install a Visy Vortex Filter
By Rain Brothers October 31, 2024
Install a Wisy Vortex Filter with ease! This step-by-step guide covers prepping the base, positioning pipes, sealing joints, and ensuring optimal filtration. Perfect for DIY homeowners ready to tackle a rewarding project.
Installing ozone generator into water tank
By Rain Brothers October 28, 2024
Keep your rainwater clean and fresh with an ozone generator and floating tether system. Learn how to install the JED 203 model in your cistern to control algae and bacteria without harsh chemicals.
How To Install Your New Springer Series Cistern Pump
By Rain Brothers October 24, 2024
Installing a cistern pump can seem daunting, especially if you're not familiar with the ins and outs of pump mechanics. Follow these quick tips to ensure a smooth setup and efficient operation.
Underground Reservoir Systems for Low Yield Wells
By Jonathan Meier October 21, 2024
In today's blog post, we're diving into the details of creating an underground reservoir for low flow, low yield wells. This method provides a more reliable water system, especially when you need more than just a 500-gallon basement tank
Submersible Pumps for Drip Irrigation
By Jonathan Meier October 9, 2024
Learn how to effectively use a submersible pump for drip irrigation. Avoid common mistakes with drip tape, emitters, and tubing, and discover solutions to optimize your irrigation system's flow and pressure.
What To Do With An Old Cistern
By Jonathan Meier July 14, 2024
Discover an old cistern in your yard? Learn how to restore or replace it with our comprehensive guide. From debris removal to ensuring water tightness, we cover all steps to make your cistern functional and valuable. Contact us for expert advice and products to ease your restoration project.
By Jonathan Meier July 1, 2024
Learn how to determine the right size for your rainwater harvesting tank with our comprehensive guide. Tailored for the Midwest U.S., our tips cover key considerations for various household sizes and usage needs.
Water Storage Systems: A Solution for Low Yield Wells
By Rain Brothers June 25, 2024
Discover effective water storage systems for low yield wells. Learn how to install a reservoir tank to ensure a consistent water supply, transforming your low-producing well into a reliable source.
Plumbing Rainwater Systems For Homes
By Jonathan Meier June 20, 2024
Learn how to effectively set up plumbing rainwater systems for homes while navigating local regulations, ensuring cost-effectiveness, and optimizing water conservation for non-potable uses like toilets, laundry, and irrigation
How To Install A Littlefuse Pumpsaver
By Jonathan Meier October 21, 2023
Learn how to protect your well pump from damage with the Little Fuse PumpSaver. This guide provides easy steps for understanding, installing, and optimizing this essential device for wells that occasionally run dry
More Posts
Share by: